Influencing factors analysis to determine standard time of operators in a gauge calibration process
Article Sidebar
Main Article Content
Abstract
Downloads
Article Details
1. Proposal of Policy for Free Access Periodics
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 that allows the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in an institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
Proposal of Policy for Periodic that offer Postponed Free Access
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 [SPECIFY TIME HERE] after the publication, allowing the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
d. They allow some kind of open dissemination. Authors can disseminate their articles in open access, but with specific conditions imposed by the editor that are related to:
Version of the article that can be deposited in the repository:
Pre-print: before being reviewed by pairs.
Post-print: once reviewed by pairs, which can be:
The version of the author that has been accepted for publication.
The editor's version, that is, the article published in the magazine.
At which point the article can be made accessible in an open manner: before it is published in the magazine, immediately afterwards or if a period of seizure is required, which can range from six months to several years.
Where to leave open: on the author's personal web page, only departmental websites, the repository of the institution, the file of the research funding agency, among others.
References
AL-SALEH, K. S. (2011) Productivity improvement of a motor vehicle inspection station using motion and time study techniques. Journal of King Saud University - Engineering Sciences, v. 23, n. 1, p. 33–41.
AMATO, D. T.; REIS, A. C. (2016) A percepção dos monitores sobre o programa de monitoria do Ensino Superior do CEFET/RJ. Scientia Plena, v. 12, n. 7, p. 1–10.
BARNES, R. M. (2004) Estudo de movimentos e de tempos: Projeto e medida do trabalho. 6 ed. São Paulo: Edgard Blücher LTDA.
CHIAVENATO, I. (2014) Introdução a teoria geral da administração. 9. ed. São Paulo: Manole.
FIGUEIREDO, F. J. S.; OLIVEIRA, T. R. C.; SANTOS, A. P. B. M. (2011) Estudo de tempos em uma indústria e comércio de calçados e injetados ltda. In: ENCONTRO NACIONAL DE ENGENHARIA DE PRODUCAO, 31, Belo Horizonte, Anais..., Belo Horizonte: Enegep.
GOLBERG, M.; CHO, H. A. (2004) Introduction to Regression Analysis. 1 ed. EUA: WIT Press.
GONÇALVES, J. L. et al. (2014) Estudo de tempo e movimento na etapa de seleção de mudas em um viveiro florestal. Floresta, v. 44, n. 4, p. 647–656.
IBGE. (2017) Agência IBGE Notícias. Avaliable: https://agenciadenoticias.ibge.gov.br/agencia-sala-de-imprensa/2013-agencia-de-noticias/releases/16555-setor-de-servicos-tem-queda-de-0-8-em-julho.html. Access: 17th September, 2017.
JACOBS, F. R.; CHASE, R. B. (2012) Administração de operações e da cadeia de suprimentos. 13 ed. Porto Alegre: McGrawHill.
LOPETEGUI, M. et al. (2014) Time motion studies in healthcare: What are we talking about? Journal of Biomedical Informatics, v. 49, p. 292–299.
MARTINS, P. G.; LAUGENI, F. P. (2015) Administração da produção. 3 ed. São Paulo: Saraiva.
NOVASKI, O.; SUGAI, M. (2002) Mtm como ferramenta para redução de custos: O taylorismo aplicado com sucesso nas empresas de hoje. Revista Produção Online, v. 2, n. 2.
PEINADO, J.; GRAEML, A. R. (2007) Administração da Produção: operações industriais e de serviços. Curitiba: UnicenP.
SANTOS, A. C. S. G. et al. (2015) Estudo de tempos e movimentos no processo de confecção de jalecos. In: ENCONTRO NACIONAL DE ENGENHARIA DE PRODUCAO, 35, Fortaleza, Anais..., Fortaleza: Enegep.
SILVA, E. L.; MENEZES, E. M. (2005) Metodologia da Pesquisa e Elaboração de Dissertação. 4 ed. Florianópolis: Universidade Federal de Santa Catarina.
SILVA, V. A. A.; GUIMARÃES, A. L.; JÚNIOR VERALDO, L. G. (2014) Aplicação de técnicas de tempos & métodos em linha de envase de óleos lubrificantes. Revista de Gestão & Tecnologia, v. 1, n. 2, p. 58–63.
SIMÕES, D.; FENNER, P. T.; ESPERANCINI, M. S. T. (2014) Produtividade e custos do Feller-Buncher e processador florestal em povoamento de eucalipto de primeiro corte. Ciencia Florestal, v. 24, n. 3, p. 621–630.